MIGHTY+ - Function Principle

MIGHTY+ - How to Clean

FILLING SET - How to Use

DOSING CAPSULES - Fill with Herbs

MIGHTY+ - Insert Dosing Capsule

Frequently Asked Questions

What is the difference between the MIGHTY+ and the MIGHTY?

What materials have been used in the MIGHTY+?

Carefully selected materials are incorporated into the design of the MIGHTY+. To be even more robust and resistant, the filling chamber of the MIGHTY+ is ceramic coated. The housing is made of a heat-resistant and tasteless plastic. The cooling unit is made of PEEK, a high-quality plastic which, due to its properties, is frequently used in room technology and in medical technology, e.g. for implants. All materials comply with FDA regulations and are "medical grade".

Why is the Filling Chamber ceramic coated now?

The ceramic coating makes the device even more robust and resistant.

Which Power Supply is suitable for the MIGHTY+?

The MIGHTY+ can be used with common power supplies featuring USB-C to USB-A. Depending on the current supply, charging will occur faster or slower.

For pass-through, a Supercharger (+15V @ 3A) is required, which can be purchased in our online shop.

Can I use the MIGHTY+ while charging?

Yes, with a power supply that provides enough current, the batteries are bridged and the so-called "pass-through charging" is possible. For this you need a Supercharger, which supplies at least 15V@3A. The "pass-through" function is confirmed on the display of the MIGHTY+ with the signal "dct".

Is the Filling Chamber Tool insert of the MIGHTY+ still the same size?

The dimensions of the insert for the Filling Chamber Tool are the same for the MIGHTY and the MIGHTY+.

How long is there a warranty when buying the MIGHTY+?

When buying a MIGHTY+ you get 2 years warranty. After registering the device in our online store, you will receive an additional one year warranty.

What is the charging time of the MIGHTY+?

The MIGHTY+ has a USB-C charging port with improved charging function. This allows the MIGHTY+ to be charged with 45 watts. The completely redesigned circuit board allows for significantly increased performance. The new charging function helps the MIGHTY+ to charge its battery to 80% in approx. 40 minutes (+15V@3A).

How to set the temperature?

The temperature range is between 40 °C and 210 °C or 104 °F and 410 °F. By pressing the minus/- or plus key for approx. 3 seconds, it is possible to change the temperature unit from °C to °F at any time. Pressing and holding the plus or minus button starts a continuous countup or countdown of the set temperature.
In addition, the MIGHTY+ has 3 preset temperatures:

Base temperature: 180°C/ 356°F
Booster temperature: Pressing the power button 2 times in a row increases the base temperature by 15°C/ 27°F.
Superbooster temperature: Pressing the power button 3 times in a row increases the booster temperature by 15°C/ 27°F.

How do I take proper care of the batteries?

You should store the MIGHTY+ at standard ambient temperature approx. 20°C, no frost, no direct sunlight, and keep it dry. If the device is not used for a longer time, you should store it at a battery capacity of between 20 % and 80 %.

When using the MIGHTY+ it is best to drain the batteries until about 20 % capacity, which is one battery bar and then recharge them fully. From time to time, it makes sense to drain them all the way and then recharge them fully; this will adjust the battery capacity and keep the battery gauge correct. If the MIGHTY+ is operated while plugged in, the batteries will be bypassed. Therefore, the MIGHTY+ can be used even with completely drained batteries if it is plugged in and switched on.

How is the vapor created?

The MIGHTY, as well as the CRAFTY and the PLENTY, functions with a patented combination of full hot air convection heating and additional conduction so that the air is already heated when it flows into the heated-up Filling Chamber and ensures an immediate and continuous vaporizing. The additional benefit of the heated Filling Chamber is that the material to be vaporized is already heated up and vapor production takes place on the first draw.

How do I exchange the lower Screen?

Press in the Screen, by using the Filling Chamber Tool along the groove of the Filling Chamber. The Screen bulges and detaches from the groove. Clean the screen with isopropyl alcohol or rinsing water or exchange it with a new Screen. Curve the cleaned or new Screen. Insert the Screen into the Filling Chamber with the curved side facing upwards. Press the Screen flat into the provided groove with the aid of the Filling Chamber Tool.